Hello Guest User,
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Search found 12 matches
- Mon Jun 15, 2020 10:46 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
Well its been a long haul,but i seem to have made some progress by going up a size on the pilot jets.The bike now holds a steady throttle with only the occasional spit back through the carbs.Hopefully with a bit of tweaking i will be there.
- Tue Sep 10, 2019 10:30 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
They seem a good option,thanks Al.
- Mon Sep 09, 2019 9:57 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
carb rubbers are new z1000j and siliconed to head. I have positioned the filters so that the air passages are clear.Maybe a new set are needed.Are there any make other than k and n that can be recommended as funds are tight at the moment. thanks guys.
- Sun Sep 08, 2019 10:01 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
Sorry for the delay getting back,house refurb taking up a lot of my time.Well the dyna s is fitted but its not the cure.At least i can rule out the pickups and igniter.When i get a chance i will pull the carbs again.the colourtune shows a yellow flame and a white flash when it spits which as im told...
- Sun Jul 07, 2019 9:52 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
I have checked the pickup coils and they seem ok with a meter.Although im not the best with electrics.Since its only past tickover to 3 thousand revs im not sure it would show up on a ohmmeter.It has a brand new set of rs34s on it.The bike was bought as a part restored non runner so any history of w...
- Tue Jul 02, 2019 10:41 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
well i put a new peg ,bolt and nut on,along with the new advancer but its still spitting and missing.Im leaning towards replacing the pickups with dyna s, as i understand i can do away with the igniter.
- Tue May 28, 2019 1:48 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
I will check through all that you mention.I know the roll pin has a flat edge.It could be that it is preventing the advancer to fit to the crank correctly.If i find the answer i will post on here.Thanks again Al.
- Sun May 26, 2019 9:41 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Re: Ignition advancer
I have put feeler gauges between the lobe and pickups and there seems to be equal clearances.I will try removing the shim and see what happens.As you say il check the nut and bolt as well.There is clearance between the shaft and pinch nut.A bit of a head scratcher this one.A problem ive been trying ...
- Sat May 25, 2019 2:59 pm
- Forum: Bike Help
- Topic: Ignition advancer
- Replies: 23
- Views: 7496
Ignition advancer
Hi guys.My gpz1100b1 refuses to rev cleanly off idle on a constant throttle.Tickover is fine and over about 3k it goes perfectly.Ive checked nearly everything and all i can find is that the mechanical advancer is not moving until i get to around 3k revs, where it flies round.If i remove one of the s...
- Fri Oct 19, 2018 11:05 pm
- Forum: Bike Help
- Topic: unitrack switch decals
- Replies: 3
- Views: 1816
Re: unitrack switch decals
Hi john.I bought some for my 900r and 1100.They are stickers but they look good and blend in well.
- Thu Mar 15, 2018 2:23 pm
- Forum: Bike Help
- Topic: Gpz1100b1 wiring
- Replies: 0
- Views: 817
Gpz1100b1 wiring
Hi guys,can somebody tell me the correct wiring sequence for the airflow meter as the p.o. had removed them from the connector.The clymer and kawasaki manuals differ from one another for the meter and computer.Ive wired the flow meter to what it says in the kawasaki manual .Ive checked all the resis...
- Wed Feb 28, 2018 1:19 pm
- Forum: New Here?
- Topic: Newbie from somerset
- Replies: 12
- Views: 6503
Newbie from somerset
just like to say hello to everyone here.Ive recently aquired a gpz1100b1 as a non runner.so hopefully with a bit of help ,we can get her up and running. thanks guys.