i am replacing the o rings in the cylinder base, can anyone advise should these be fitted by pressing down fully into recess or just left slightly proud of the block.
also recommendation for gasket compound for camshaft end plugs and was going to use around block oilways as per manual
thanks
Hello Guest User,
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Search found 12 matches
- Mon Aug 29, 2022 1:13 pm
- Forum: Bike Help
- Topic: z1000 a1 cylinder base o rings and gasket compound
- Replies: 0
- Views: 227
- Wed Jun 08, 2022 4:52 pm
- Forum: Wanted Adz
- Topic: camshafts for z1000 A1 wanted
- Replies: 9
- Views: 1288
Re: camshafts for z1000 A1 wanted
thanks jerry, arrived safely today , spot on.
cheers
john
cheers
john
- Sun May 29, 2022 10:07 pm
- Forum: Wanted Adz
- Topic: camshafts for z1000 A1 wanted
- Replies: 9
- Views: 1288
Re: camshafts for z1000 A1 wanted
guys many thanks for advice , are the sprockets all the same mounting hole positions as i have my originals if i can swop them over?
- Sun May 29, 2022 10:37 am
- Forum: Wanted Adz
- Topic: camshafts for z1000 A1 wanted
- Replies: 9
- Views: 1288
camshafts for z1000 A1 wanted
can anybody help with a set of camshafts for a 1977 Z1000A1.
thanks
john
thanks
john
- Sat May 28, 2022 12:39 pm
- Forum: Bike Help
- Topic: camshaft repair / replacement question Z1000A1
- Replies: 13
- Views: 1656
Re: camshaft repair / replacement question Z1000A1
exhaust shim , if the lobe hard facing is "mullered" is it something that is recoverable ? Cams cam be re-faced but the cost may be more than picking up another good used set . You would need to contact one of the cam shops i mentioned to find out. All the z900-1000 kickstart motor cams a...
- Wed May 25, 2022 7:58 am
- Forum: Bike Help
- Topic: camshaft repair / replacement question Z1000A1
- Replies: 13
- Views: 1656
Re: camshaft repair / replacement question Z1000A1
The journals are fine if within tolerances, the cam lobe looks like the hard facing is mullered. Possibly heat related and infrequent oil changes. What's the shims like on the affected lobes. Some aftermarket shims are poor quality and can cause lobe damage. exhaust shim , if the lobe hard facing i...
- Mon May 23, 2022 9:12 am
- Forum: Bike Help
- Topic: camshaft repair / replacement question Z1000A1
- Replies: 13
- Views: 1656
Re: camshaft repair / replacement question Z1000A1
pictures of camshafts, the marking on the lobe is the exhaust cam , this is the cylinder that was oiling up and on examination has damaged vale stem oil seal. hope these pictures help, thanks again.
john
john
- Sun May 22, 2022 1:09 pm
- Forum: Bike Help
- Topic: camshaft repair / replacement question Z1000A1
- Replies: 13
- Views: 1656
camshaft repair / replacement question Z1000A1
Z1000 a1 : this is all new to me so not sure if cams can be repaired? There is some scoring on journals and looks like some kind of wear on exhaust lobe, looks like when chrome wears off parts showing zinc underneath. Any suggestions regarding experts in the northwest area? Hope this makes sense, an...
- Sun Jul 22, 2018 10:03 am
- Forum: Bike Help
- Topic: Carb rebuild Z1000 A1 Lubrication?
- Replies: 1
- Views: 998
Carb rebuild Z1000 A1 Lubrication?
mikuni carbs i was wondering should i lubricate the Throttle Valve Bracket , the rose joint ball. i have striped the mikuni carbs and sonic cleaned them but didn't clean the bracket and ball joint as i wasn't sure about lubricating the joint. i have managed to source a replacement adjuster and refer...
- Sun Jul 08, 2018 10:45 am
- Forum: Bike Help
- Topic: z1000 a1 mikuni carb adjuster
- Replies: 5
- Views: 2271
Re: z1000 a1 mikuni carb adjuster
thanks for quick response , will give them a try
- Sat Jul 07, 2018 7:50 pm
- Forum: Bike Help
- Topic: z1000 a1 mikuni carb adjuster
- Replies: 5
- Views: 2271
z1000 a1 mikuni carb adjuster
hi just got my 1977 z1000 a1 an upon trying to adjust the carbs with morgan carb balancer two of the screw adjusters at the top of the slides are damaged,the screw slot is worn and i cant properly adjust them. does any one know either part number or supplier of replacements ,all my searches have pro...
- Wed Jul 04, 2018 8:52 am
- Forum: New Here?
- Topic: new member
- Replies: 11
- Views: 5844
new member
:) Hi just introducing myself just got a 1977 Z1000 A1 ,its originaly a USA import. not standard paint its more a lime green , Pipe sounds lovely. some minor problems but i will ask you experts for advice. this is my second Z1000 A1 the first i purchased in 1977 brand new from ormskirk kawaski centr...