Hello Guest User,

Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.

To access these 'Registered Users Only' areas simply register and login.

My newly acquired '77 kz900a5

Post pictures of your bikes without having to pull them to bits to qualify for Projects. Club eligible Z based bikes only please, anything else should be in the bottom shed.
Please use it wisely and be respectful of other peoples' pride and joy....
Message
Author
User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

#31 PostAuthor: Ultim8pc » Mon Dec 26, 2016 4:46 pm

Actually Tony Archer couldn't have been less interested if he tried..
Told me to buy a seat cover from Z Power and do it myself....

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

#32 PostAuthor: Ultim8pc » Tue Jan 31, 2017 2:44 pm

Managed to source a decent conditon OEM RH sidepanel and badge to replace the aftermarket one which had no badge.
Image

User avatar
Zedorset
100Club
100Club
Posts: 217
Joined: 16th Oct 2016
Location: Blandford, Dorset.

#33 PostAuthor: Zedorset » Tue Jan 31, 2017 3:11 pm

They are only original once. There must be a period seat out the somewhere!

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

#34 PostAuthor: Ultim8pc » Tue Jan 31, 2017 3:27 pm

Zedorset wrote:They are only original once. There must be a period seat out the somewhere!

True. I think I am going to get a new seat foam and recover the existing seat base.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#35 PostAuthor: Ultim8pc » Thu Jun 15, 2017 8:42 pm

So, finally got some time to start work on the 900.
Started taking bits off the to clean up and I think it will tidy up well enough.
Did the valve clearances yesterday, a couple were well tight and had to go down three sizes to get them in tolerance. (eek!). Cams lobes look in good condition.
Checked the compression with the engine cold and got 85/95/90/85 psi. Will have to start her up and check warm but the cold readings look respectable I think.
I look at sorting the oil leaks next (tacho drive, alternator wire and gear change shaft).
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
paul doran
Area Rep.
Area Rep.
Posts: 9139
Joined: 24th Sep 2004
Location: near Dublin Ireland

Re: My newly acquired '77 kz900a5

#36 PostAuthor: paul doran » Sun Jun 18, 2017 9:14 am

100 is the working range
You may have a few seized rings
Pour diesel or hot waste oil into bores and leave it for a few days
Then redo the compression test
way too many Zeds

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#37 PostAuthor: Ultim8pc » Tue Jun 20, 2017 11:01 pm

Re-did the tests with some oil in the bores and got
115/120/120/125
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#38 PostAuthor: Ultim8pc » Sat Jun 24, 2017 11:47 am

Stripped the carbs down to run them through the ultrasonic cleaner.
Again, other than the grot caused by leaky float bowl gaskets - they are in excellent condition with pretty much no wear.
Had a couple of screws that wouldn't come out without the use of the mole grips...
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#39 PostAuthor: Ultim8pc » Tue Jul 18, 2017 6:04 am

Been a bit ill for the last few weeks, so not moved forward too much.
However, upon closer inspection the float needles are a tad work, so I have full refurb kits ready to fit.
Taken the sump off and it's all pretty clean with no crap in the oil pump gauze filter. Getting the old sump gasket off was a complete bastard as it was hard as rock..
Going to fit a new oil pump o-ring as the existing one is a bit hard. Also fitting a new seal and o-ring to the tacho drive.
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#40 PostAuthor: Ultim8pc » Sun Aug 06, 2017 9:14 pm

Finally well enough to get more work done.
Carbs all re-assembled, with float valves, o-rings and gaskets.
Image
Image
Image
Image

I also removed the sump, cleaned it up and the front of the crankcases, fitted new oil pump and oil filter o-rings.
No debris in the sump (just some thick oily gunge) and no crap in the pump gauze.
Image
Image
Image
Image
Image
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#41 PostAuthor: Ultim8pc » Thu Dec 14, 2017 4:04 pm

Been a bit busy with other stuff, but I have been doing some work as time permits:
Stripped out the wheels, forks and swing arm and cleaned everything up.
Bought a new battery and also managed to pick up a very nice condition Kerker to replace the tatty one that's currently fitted.
Need to buy a standard seat cover and I have discovered that the rear brake return spring is broken, so will need to get one.
Hoping to get it all reassembled by Christmas and then I can start on getting it registered!
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#42 PostAuthor: Ultim8pc » Sat Dec 30, 2017 11:27 am

A bit more progress:
Not had much time as I have been busy setting up a new business venture.
However, bought a return spring and a seat cover. Managed to salvage a good OEM seat foam from another seat which has a rotted base and non-standard cover. So I'll get on with recovering it this week.
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#43 PostAuthor: Ultim8pc » Sun Jan 28, 2018 9:55 pm

Got quite a bit done since the last update.
Used the original base and used an original foam from another seat with a crappy base and fitted a new cover. Not a bad job if I say so myself
Image
Image
Image
Image
Image

Reassembled all the rear end of the bike and electrics.
Used Quick-Glo P3-Ultra (plug-plug) to clean up and refinish the rear inner mudguard, tools carrier, airbox and document holder.
Image
Image

Also, refitted the drive shaft cover after fitting new oil seals.

Starting to look like a bike again. With a fair wind I can get it finished this week!
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#44 PostAuthor: Ultim8pc » Sun Jan 28, 2018 9:59 pm

Oh and I swapped the carb pairs around so the air screws were facing the right way. :oops:
And fitted new fuel T-pieces while I was at it, even though the ones removed didn't look too bad.
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.

User avatar
Ultim8pc
Hardcore
Hardcore
Posts: 2130
Joined: 5th Sep 2014
Location: Keighley, West yorkshire
Contact:

Re: My newly acquired '77 kz900a5

#45 PostAuthor: Ultim8pc » Tue Feb 20, 2018 11:32 pm

Work done since last update:
Carb float heights set and carbs refitted to bike
swing arm, and rear wheel refitted
New foot peg mount rubbers fitted
Front brake caliper stripped and new pads fitted
Engine cleaning work
Trimmed excess material from new seat cover and glued down edges to base
---
Currently stripping the tatty lacquer from the front forks
Not long till it's finished!
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.


Return to “Show us Yours”

Who is online

Users browsing this forum: No registered users and 26 guests