Hello Guest User,

Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.

To access these 'Registered Users Only' areas simply register and login.

UNLIMITED LTD - The Pigford Project

Work in Progress

Moderators: chrisu, paul doran, Taffus, KeithZ1R

Post Reply
Message
Author
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#91 PostAuthor: Pigford » Sat Jan 30, 2016 5:22 pm

Done a few bitz here & there.

Fitted the alloy engine mountings (cheers Padders)...

Image

Image

Carbs stripped & cleaned... 28mm Miks with K&N twin filters...

Image

Also the grab rail (thanx Gary) and some winkers (rare items for me)...

Image


Still got to tackle the wiring - gonna start that tomorrow :??
And on the 7th day... Zeds were created!
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#92 PostAuthor: Pigford » Sun Jan 31, 2016 12:43 pm

First time she's ran for a long time !!!!!


Carb's need some sorting (leaking a bit - jetting's out too) and rest of wiring sorted, but it's getting there.


https://youtu.be/3GgNepwBoQg


Don't think it'll ready in time for the ACE Cafe though :evil:
And on the 7th day... Zeds were created!
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#93 PostAuthor: Pigford » Wed Feb 03, 2016 5:27 pm

Thanx to my quick reactions - and Padders, I now had a mint set of RS34's stuck on me Harris....


Image


Image


...... which replace the loverly VM28 carbs which I got from Adrian H a while back (off a GS1000?) but are now going to be used on my Z1000 LTD :twisted:
And on the 7th day... Zeds were created!
Top
User avatar
RALPHARAMA
Area Rep.
Area Rep.
Posts: 2752
Joined: 19th May 2007
Location: Pensford, Somerset
Contact:
Contact RALPHARAMA

#94 PostAuthor: RALPHARAMA » Wed Feb 03, 2016 6:15 pm

Can we now assume tharris isn't been punted on? Defo right carbs for the bike :D
Ralph Ferrand
Z1000A1 (1977), Godier Genoud Z1300A5 (1983), Z900A4 Stock (1976), Z900A4 Special (project), GPZ1100 Unitrak (1983), ZRX1200R (2004) DT175MX (1981).

http://www.bikerstoolbox.co.uk

Don't be caught out http://www.dhlparcels.info/
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#95 PostAuthor: Pigford » Wed Feb 03, 2016 8:11 pm

vduk wrote:Can we now assume tharris isn't been punted on? Defo right carbs for the bike :D


Ralphy - you is correct old bean... gone past that dodgy area and decided I'll hang on to the Harris for the moment. It's great only having 4 x bikes to step around... so I can get stuck into me bikes "as and when".

Looking forward to the S.W Rally 2016 - that's my realistic aim for this project :twisted:
And on the 7th day... Zeds were created!
Top
Is Vic There
Hardcore
Hardcore
Posts: 1285
Joined: 8th Nov 2011
Location: Brisbane, Australia.

#96 PostAuthor: Is Vic There » Thu Feb 04, 2016 3:14 am

Can you let me know what cables you use, better still before you get them can I talk to you, I need cables for my Harris and it would be good if you could get a set made up for me when you do it!

Image

Image
Norton 850 Command, Harris Mag 2, Harris Mag 5, Triumph Steve McQueen, Suzuki RGV250 Barry Sheene, RG250 Walter Wolf, RD125LC, Lambretta Li150, Vespa 50N.
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#97 PostAuthor: Pigford » Thu Feb 04, 2016 7:08 am

WIRING :shock:

TBH, you probably don't wanna copy my efforts. :oops:


1] My Harris is already finished - I did it a couple of years back.
2] It defo is NOT the neatest arrangement :lol:
3] I got several different colours from VWP (Vehicle Wiring Products) and just did it.

Most of the modern wires take higher loads than the original stuff. I also solder all connections (spades, butts, bullets, etc).

There are some photo's way back in Projects Section somewhere.... I'll dig them out later today :wink:
And on the 7th day... Zeds were created!
Top
Is Vic There
Hardcore
Hardcore
Posts: 1285
Joined: 8th Nov 2011
Location: Brisbane, Australia.

#98 PostAuthor: Is Vic There » Thu Feb 04, 2016 10:02 am

I'm on about the throttle cable mate :lol:
Norton 850 Command, Harris Mag 2, Harris Mag 5, Triumph Steve McQueen, Suzuki RGV250 Barry Sheene, RG250 Walter Wolf, RD125LC, Lambretta Li150, Vespa 50N.
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#99 PostAuthor: Pigford » Thu Feb 04, 2016 1:21 pm

:oops: T'was your daft accent that confused me :roll:


I'm using an R1 throttle assembly....... but the inner was a bit long on the push side. So I got a universal set off Venhill and cobbled a new Pusher. Came with various nipples (snigger). There was a little blob of solder one end and it had a small nipple that fits the throttle end.... so I just had to cut it to length (Dremel with disc ) then at the carb end I used a screw-tight nipple to fit :wink:

I never have much luch soldering - probably coz they're s/s cables!

Photo's later
And on the 7th day... Zeds were created!
Top
Is Vic There
Hardcore
Hardcore
Posts: 1285
Joined: 8th Nov 2011
Location: Brisbane, Australia.

#100 PostAuthor: Is Vic There » Thu Feb 04, 2016 7:21 pm

Nice one, interested in the bend at the carb side!
Norton 850 Command, Harris Mag 2, Harris Mag 5, Triumph Steve McQueen, Suzuki RGV250 Barry Sheene, RG250 Walter Wolf, RD125LC, Lambretta Li150, Vespa 50N.
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#101 PostAuthor: Pigford » Thu Feb 04, 2016 8:35 pm

Now the RS34's are on me Harris..... I fitted the VM28's (GS1000?) on the Z1000 - and she runs real sweet (apart from the blowing zorst) :twisted:

https://youtu.be/8AiNn3RUyHg

Just need to finish the rest of the wiring now :cloud
And on the 7th day... Zeds were created!
Top
Coose
Custard Cream
Custard Cream
Posts: 703
Joined: 20th Apr 2015
Location: North Yorks

#102 PostAuthor: Coose » Thu Feb 04, 2016 8:51 pm

That swinging arm is so ridiculous it's fantastic! :D
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#103 PostAuthor: Pigford » Fri Feb 05, 2016 7:21 am

Coose wrote:That swinging arm is so ridiculous it's fantastic! :D


It's been stashed away for so long - I just had to use it :lol:
And on the 7th day... Zeds were created!
Top
User avatar
Pigford
I'm on prescription!!
Posts: 10566
Joined: 2nd Jan 2006
Location: Hampshire Coast UK

#104 PostAuthor: Pigford » Thu Feb 25, 2016 7:06 pm

Got me nice Marshall, glycerine filled oil pressure gauge from the USA...

Image

.... gotta be worth another 5 mph :twisted:
And on the 7th day... Zeds were created!
Top
User avatar
Ginger Bear
Hardcore
Hardcore
Posts: 5512
Joined: 16th Dec 2008
Location: In the Dark.
Contact:
Contact Ginger Bear

#105 PostAuthor: Ginger Bear » Thu Feb 25, 2016 7:13 pm

Pigford wrote:
.... gotta be worth another 5 mph :twisted:



Yeah.......... Slower, when you look down and it's reading zilch. :eek :eek
Image

# 104

Phil Churchett Award Winner 2011 & 2016 :D
Buzzworkz Best Modified Zed 2016
Top
Post Reply

Return to “Projects”

Who is online

Users browsing this forum: No registered users and 18 guests