Hello Guest User,

Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.

To access these 'Registered Users Only' areas simply register and login.

The ZPower Project

Work in Progress

Moderators: chrisu, paul doran, Taffus, KeithZ1R

Message
Author
User avatar
zpower
100Club
100Club
Posts: 325
Joined: 21st Feb 2013
Location: Staffordshire
Contact:

The ZPower Project

#1 PostAuthor: zpower » Fri Mar 22, 2013 1:22 am

Hi all,

The project is based around a GPZ1100 A2 frame.

The engine is a Z1000 A1 (1977)

The idea (Plan A) is to build a vague silhouette of a Z1 but mono shocked so I will be using Z1 paintwork etc...

The plan is to only modify the frame to accommodate the project requirements so everything else can be readily bought of the shelf and therefore more easily upgraded at a later date.

Not surprisingly none of the paintwork currently fits in any shape or form.

I slipped (well not quite but hey ho) the frame over the engine to see what initial mods needed doing...

Image

The first immediately obvious obstacle was the rear suspension mounting bracket which is stopping the engine from dropping in. It also gets in the way of the ZX6R swinging arm.

Image

It is to late to start on it today but I have some micro adjusters at the ready... :D

Image

To be continued....
Last edited by zpower on Mon Feb 29, 2016 6:52 pm, edited 1 time in total.

User avatar
zpower
100Club
100Club
Posts: 325
Joined: 21st Feb 2013
Location: Staffordshire
Contact:

#2 PostAuthor: zpower » Fri Mar 22, 2013 8:28 pm

First tentative micro incisions made :D

The engine now sits in the frame and initial look at the swinging arm and tail piece fitment...

Image

Swinging arm clears JUST :D

Image

Top down view of just how close things are...

Image

Then engine can move a little further forward but can't line anything up just yet.

Happy so far :D

garyd
Hardcore
Hardcore
Posts: 2267
Joined: 11th Jun 2011
Location: West of London

#3 PostAuthor: garyd » Fri Mar 22, 2013 9:25 pm

Really interested how this goes as I have a very similar project in the garage.

I have had ZERO luck in getting any tank to fit.

best effort so far was to completly screw up a Ltd tank by taking a lump hammer to the inside

Just cant find anything that will fit the wider frame tubes at the rear of the tank.

Next effort is to cut out the inner of a GPz tank and try to mate that to a tear drop outer.
I can only see tears comming from that. !!

kev edwards
Hardcore
Hardcore
Posts: 2051
Joined: 3rd Apr 2009
Location: leverington UK

#4 PostAuthor: kev edwards » Sat Mar 23, 2013 10:50 am

garyd wrote:Really interested how this goes as I have a very similar project in the garage.

I have had ZERO luck in getting any tank to fit.

best effort so far was to completly screw up a Ltd tank by taking a lump hammer to the inside

Just cant find anything that will fit the wider frame tubes at the rear of the tank.

Next effort is to cut out the inner of a GPz tank and try to mate that to a tear drop outer.
I can only see tears comming from that. !!

have you thought about a zephyr tank?

oldtimer
100Club
100Club
Posts: 217
Joined: 2nd Mar 2013
Location: stoke on trent

#5 PostAuthor: oldtimer » Sat Mar 23, 2013 11:01 am

kev edwards wrote:
garyd wrote:Really interested how this goes as I have a very similar project in the garage.

I have had ZERO luck in getting any tank to fit.

best effort so far was to completly screw up a Ltd tank by taking a lump hammer to the inside

Just cant find anything that will fit the wider frame tubes at the rear of the tank.

Next effort is to cut out the inner of a GPz tank and try to mate that to a tear drop outer.
I can only see tears comming from that. !!

have you thought about a zephyr tank?

Have you tried to find a second hand Zephyr tank? Like rocking horse s*%t ! :shock:

dixiethedog
Custard Cream
Custard Cream
Posts: 704
Joined: 14th Feb 2009
Location: new hartley newcatle upon tyne

#6 PostAuthor: dixiethedog » Tue Mar 26, 2013 2:34 pm

Nice project. Ive a gpz750 uni trac that Im going to fit z1 panels too.
Fitting the tank is a peice of cake,if you have a welder?
Simply copy what has been done in the link. :D

http://www.oldskoolperformance.com/foru ... 8&start=14

i tried to fit a different tank to a frame that didnt want the tank to fit (Im not sure what bike it was now?),with a hammer to the base of the tank. :roll: Never again! Frames are lot easier to modify!
Good luck. :D
Every silver lining has a cloud...

garyd
Hardcore
Hardcore
Posts: 2267
Joined: 11th Jun 2011
Location: West of London

#7 PostAuthor: garyd » Tue Mar 26, 2013 6:46 pm

The 750 Zephyr looks most like the Z1 tank, but your right...just don't come available unless they have a dent in...even thought about buying a bike and selling off all the other bits...but they still go for £1500..too rich for me!

I'm sure I can make this Plug'N'Play...just need to keep doing my research.

garyd
Hardcore
Hardcore
Posts: 2267
Joined: 11th Jun 2011
Location: West of London

#8 PostAuthor: garyd » Tue Mar 26, 2013 6:52 pm

That's too serious a mod on the frame for me...I do have a habit of 'finding the limit' of bikes chassis :lol: :lol:

dixiethedog
Custard Cream
Custard Cream
Posts: 704
Joined: 14th Feb 2009
Location: new hartley newcatle upon tyne

#9 PostAuthor: dixiethedog » Wed Mar 27, 2013 9:40 am

kev edwards wrote:
garyd wrote:Really interested how this goes as I have a very similar project in the garage.

I have had ZERO luck in getting any tank to fit.

best effort so far was to completly screw up a Ltd tank by taking a lump hammer to the inside

Just cant find anything that will fit the wider frame tubes at the rear of the tank.

Next effort is to cut out the inner of a GPz tank and try to mate that to a tear drop outer.
I can only see tears comming from that. !!


Cutting a couple of frame tubes is a lot easier than trying to weld the base of a diffferent tank in with the chance of fuel leaks. But good luck to you Gary! lol.
Just get the grinder out and cut the frame!!!!!!!!
Every silver lining has a cloud...

User avatar
zpower
100Club
100Club
Posts: 325
Joined: 21st Feb 2013
Location: Staffordshire
Contact:

#10 PostAuthor: zpower » Fri Sep 06, 2013 2:04 pm

Hi all,

Sorry it's been so long but my account was foo barred but Taffus has now sorted it for me.

Right lets have a look at getting the Z1 tank on the GPZ1100 A2 frame.

First do some measuring then a couple of micro incisions in to the old bent frame and remove side rails from the GPZ frame.


Image

Vuala...

Image

A couple of bits to trim off the GPZ frame and tidy.

Image

Right ready for welding.
** Special rates for the Z1OC forum members **
Website design, hosting / domain names.
Computer and Laptop repairs.

User avatar
Jay1969
Hardcore
Hardcore
Posts: 2891
Joined: 26th Feb 2013
Location: East Midlands, England.
Contact:

#11 PostAuthor: Jay1969 » Fri Sep 06, 2013 4:44 pm

This is awe-inspiring, looking forward to seeing more progress.
Just like to say thank you to Z-Power for the replica Z1 body kit I bought
from their online store recently, very pleased with it :up

User avatar
paul doran
Area Rep.
Area Rep.
Posts: 9140
Joined: 24th Sep 2004
Location: near Dublin Ireland

#12 PostAuthor: paul doran » Fri Sep 06, 2013 5:01 pm

Your a brave Man cutting a frame as You have
way too many Zeds

User avatar
coldsummer
Hardcore
Hardcore
Posts: 1896
Joined: 29th Jun 2009
Location: Berkeley

#13 PostAuthor: coldsummer » Fri Sep 06, 2013 5:51 pm

This looks really interesting, looking forward to seeing how it turns out.

My Z1b had the fuel tank 'widened' to accommodate some chunky top tube braces but I guess altering the frame is another option.

User avatar
zpower
100Club
100Club
Posts: 325
Joined: 21st Feb 2013
Location: Staffordshire
Contact:

#14 PostAuthor: zpower » Sat Sep 07, 2013 4:31 pm

Ok done just a bit of tidying up to do :)

Image

Image

Image

Image

Image

With the tank on...

Image

Image

Image

And what it looks like fitted...

Image

Image

It all appears to have remained straight but I will be getting it jigged up and tested when I have finished by the guru known as Martin Russell. He did loads of our one off stuff for our Harris's back in the day including straigntening a few of our frames he he :)

He did the yoke conversion for me ZX6R on to GPZ1100 stem.

Next on the agenda is the rear suspension line up and welding :)
Last edited by zpower on Tue Sep 09, 2014 12:05 pm, edited 1 time in total.
** Special rates for the Z1OC forum members **

Website design, hosting / domain names.

Computer and Laptop repairs.

sanderz
Custard Cream
Custard Cream
Posts: 847
Joined: 2nd Mar 2010
Location: Manchester

#15 PostAuthor: sanderz » Sun Sep 08, 2013 8:39 am

Liking this, keep us posted on your progress :up

Just a thought - have you tried the 'lock' now the front end is in, and the tank is on?
I know others have moved the tank locations back slightly (10mm or so but be aware of the tap fitment) to achieve more lock. Easier to do it now and alter 'lock stops' / tank mounts at this stage. Like I say only thinking out loud here ......a grown up will correct me here im sure.
Wots up DOHC


Return to “Projects”

Who is online

Users browsing this forum: No registered users and 47 guests