Hello Guest User,
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
vm28ss
Moderators: KeithZ1R, chrisu, paul doran, Taffus
- 8 Valve Mark
- Custard Cream
- Posts: 967
- Joined: 3rd Nov 2016
- Location: Glasgow, tropical west Scotland
vm28ss
i recently bought some pumper carbs which came with no air screws or springs!!!. does anyone know how long they should be?? (screws +springs) probably the same as non-pump vm28 but I'd like to be sure before ending up with wrong ones. cheers in advance.. m
- warren3200gt
- Hardcore
- Posts: 2899
- Joined: 13th Jun 2014
- Location: Dartford Kent
Re: vm28ss
give the guys at Allens performance a ring to be sure. They will also have the parts you need.
http://www.allensperformance.co.uk/shop/
http://www.allensperformance.co.uk/shop/
PUM 488 June 2023
76 Z900A4, 77 Z650B1, 77 KZ650B1, 77 Z1000A1, 82 Z1000J2, ZRX1100R.
76 Z900A4, 77 Z650B1, 77 KZ650B1, 77 Z1000A1, 82 Z1000J2, ZRX1100R.
- 8 Valve Mark
- Custard Cream
- Posts: 967
- Joined: 3rd Nov 2016
- Location: Glasgow, tropical west Scotland
Re: vm28ss
thanks Warren, I'll check the link, i have possibly sourced some already, but the seller has various lengths. I'm aiming to test run the carbs then possibly fit keyster kits if required. cheers m
Re: vm28ss
Mark,
I've got a set of 28mm pumpers from a 1000. I can check them and let you know if you'd like?
I've got a set of 28mm pumpers from a 1000. I can check them and let you know if you'd like?
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.
- 8 Valve Mark
- Custard Cream
- Posts: 967
- Joined: 3rd Nov 2016
- Location: Glasgow, tropical west Scotland
Re: vm28ss
yes please nigel the top of the thread to the tip and the spring length would be much appreciated. thank you very large!! mark
Re: vm28ss
The ones fitted seem to be quite a way down the passage way so I'm wondering of not original or correct. However, they came off a running bike which had just been setup on the dyno...
24mm Total length
19mm tip to bottom of thread
I forget to measure thew spring length, but will do.
Hope this helps
24mm Total length
19mm tip to bottom of thread
I forget to measure thew spring length, but will do.
Hope this helps
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.
- 8 Valve Mark
- Custard Cream
- Posts: 967
- Joined: 3rd Nov 2016
- Location: Glasgow, tropical west Scotland
Re: vm28ss
that's great nigel, super rapid too..i hope you counted the turns on yours? cheers matey. m
Re: vm28ss
8 Valve Mark wrote:that's great nigel, super rapid too..i hope you counted the turns on yours? cheers matey. m
No worries, I'll need top remember to measure the spring length too..
http://www.airevalleyclassics.co.uk
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.
10% discount code Z1OCTEN
Keyster rebuild kits & carburettor spares - airscrews, jets, needles, starter plungers & gaskets.
Also petrol/ethanol proof float bowl gaskets. IMD pistons preferred seller.
- 8 Valve Mark
- Custard Cream
- Posts: 967
- Joined: 3rd Nov 2016
- Location: Glasgow, tropical west Scotland
Re: vm28ss
no rush mate,re springs; just whenever, if you can be bothered, screws are hopefully not an issue now thanks to your help.. cheers mark.
Who is online
Users browsing this forum: phil1r and 25 guests