With that profit I decided to "re-invest" rather than let Mrs P get hold of it all......
It was local and running nicely, all 19bhp of it
Not bad and with the deal for selling the W650, I still have £130 left to spend on this one
Hello Guest User,
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.
To access these 'Registered Users Only' areas simply register and login.
Z250 C
Moderators: KeithZ1R, chrisu, paul doran, Taffus
Z250 C
Following on from a recent "W650 project" viewtopic.php?f=12&t=39203&start=15 which after a good inspection I sent on for a tidy profit, although that was not the initial plan, but it was too far gone!
With that profit I decided to "re-invest" rather than let Mrs P get hold of it all......
It was local and running nicely, all 19bhp of it
Not bad and with the deal for selling the W650, I still have £130 left to spend on this one
With that profit I decided to "re-invest" rather than let Mrs P get hold of it all......
It was local and running nicely, all 19bhp of it
Not bad and with the deal for selling the W650, I still have £130 left to spend on this one
And on the 7th day... Zeds were created!
Re: Z250 C
She looks nice tidy, that's one helluva seat, in some parts of the world you can carry the whole family including the mother in law 
1975 Kawasaki Z1B
1979 Triumph Bonneville T140D
1969 BSA B25 Starfire
1979 Triumph Bonneville T140D
1969 BSA B25 Starfire
Re: Z250 C
Spent the last couple of evenings "settling" the little bike into its new home..... new plug, new HT cap, fresh plug & oil, pumped up tyres and general check over.
One reason the bike came cheap was it had a tendency to cut-out at high revs, so I stripped the carb, checked float levels, jets, needle setting, points, timing, etc. Bike starts and idles nicely.
Went out for a longer run today (now insured) and it started cutting out after a mile or so It recovered if you went careful (40mph) on slight throttle.
Soon as opened throttle started kangarooing - stopped as it stalled and it started up a few seconds later so I got back home slowly.
Off with carb again and also check flow from tank - no shit and fuel cap breathing okay.... has to be fuel starvation?
This time also checked valve clearances and they were both a shade TIGHT
Set them to 0.1mm and 0.2mm (in - ex) and off for another test ride.
Result... sorted
Gonna enjoy riding this thing to work in the sunshine.
One reason the bike came cheap was it had a tendency to cut-out at high revs, so I stripped the carb, checked float levels, jets, needle setting, points, timing, etc. Bike starts and idles nicely.
Went out for a longer run today (now insured) and it started cutting out after a mile or so
It recovered if you went careful (40mph) on slight throttle.Soon as opened throttle started kangarooing - stopped as it stalled and it started up a few seconds later so I got back home slowly.
Off with carb again and also check flow from tank - no shit and fuel cap breathing okay.... has to be fuel starvation?
This time also checked valve clearances and they were both a shade TIGHT
Set them to 0.1mm and 0.2mm (in - ex) and off for another test ride.Result... sorted
Gonna enjoy riding this thing to work in the sunshine.And on the 7th day... Zeds were created!
Re: Z250 C
Gonna enjoy riding this thing to work in the sunshine.
Is it sunny where you are then? Bloody chucking it down here!!
That motor looks familiar - Same as my 1979 KL250 I think.
Re: Z250 C
csx355 wrote:Gonna enjoy riding this thing to work in the sunshine.
Is it sunny where you are then? Bloody chucking it down here!!
That motor looks familiar - Same as my 1979 KL250 I think.
It was sunny - briefly...... and yes, the motor is v. similar to KL250, it has bigger valves, but has no kickstart!
And on the 7th day... Zeds were created!
Re: Z250 C
Just waiting for a guy to finish welding up a stainless pipe for mine, stick on some decals and I'm done.
Suns just come out down here!
- kl250.JPG (43.01 KiB) Viewed 4674 times
Suns just come out down here!
Who is online
Users browsing this forum: No registered users and 2 guests