Hello Guest User,

Please feel free to have a look around the forum but be aware that as an unregistered guest you can't see all of it and you can't post.

To access these 'Registered Users Only' areas simply register and login.

Indicator wont flash

Need help restoring, building, or finding then try here.

Moderators: KeithZ1R, chrisu, paul doran, Taffus

Post Reply
Message
Author
User avatar
sneck
100Club
100Club
Posts: 114
Joined: 31st Oct 2002
Location: Doncaster

Indicator wont flash

#1 PostAuthor: sneck » Thu May 24, 2007 8:31 pm

Z1b , For some reason the L/H indicator ( turn signal )wont flash but lights up front and rear , the R/H side works fine (ie flashes) any ideas ?
_________________
Top
User avatar
uk kev
ZedHead
ZedHead
Posts: 1184
Joined: 13th Aug 2006
Location: Berkshire

#2 PostAuthor: uk kev » Thu May 24, 2007 8:49 pm

try swapping the bulbs over from left to right, also check earths on left side, odds on it is a bad contact somewhere. do you have a hazzard switch, if so do they all work on hazzard?
Top
User avatar
Dodgy Z1B
100Club
100Club
Posts: 297
Joined: 18th Apr 2007
Location: Renfrewshire, Scotland
Contact:
Contact Dodgy Z1B

Wont flash

#3 PostAuthor: Dodgy Z1B » Thu May 24, 2007 9:06 pm

If uk Kevs suggestions dont work it may be the flasher unit m8.
Image
Top
User avatar
sneck
100Club
100Club
Posts: 114
Joined: 31st Oct 2002
Location: Doncaster

#4 PostAuthor: sneck » Thu May 24, 2007 9:21 pm

no hazzard fitted to Z1b , will have a look at what you suggested and report back , THANKS
Top
User avatar
RALPHARAMA
Area Rep.
Area Rep.
Posts: 2752
Joined: 19th May 2007
Location: Pensford, Somerset
Contact:
Contact RALPHARAMA

#5 PostAuthor: RALPHARAMA » Thu May 24, 2007 10:09 pm

Does the idiot light illuminate on the panel? If that bulb has gone tha might explain it.
Ralph Ferrand
Z1000A1 (1977), Godier Genoud Z1300A5 (1983), Z900A4 Stock (1976), Z900A4 Special (project), GPZ1100 Unitrak (1983), ZRX1200R (2004) DT175MX (1981).

http://www.bikerstoolbox.co.uk

Don't be caught out http://www.dhlparcels.info/
Top
Jerry
President
President
Posts: 635
Joined: 22nd Dec 2001
Location: Birmingham
Contact:
Contact Jerry

#6 PostAuthor: Jerry » Fri May 25, 2007 3:57 pm

Check the LH bulbs, one will either be a lower wattage, should be 21w, or one will just be a friday afternoon bulb that isn't drawing the right current. It isn't the flasher unit or the tell-tale, as they work the same in either side circuit.
Top
User avatar
z1bnackerkwacker
100Club
100Club
Posts: 407
Joined: 20th May 2006
Location: Swansea

#7 PostAuthor: z1bnackerkwacker » Fri May 25, 2007 11:26 pm

My idiot light doesn't flash but all 4 indicators work o.k, had plenty of probs' with bad earths and dodgy bulb holders and switch, plenty of Wd cured all my probs'...
Top
Rich
Hardcore
Hardcore
Posts: 1981
Joined: 4th Mar 2003

#8 PostAuthor: Rich » Sat May 26, 2007 8:39 am

High resistance cable / earth / connector / switch contacts swap the bulbs around first ( the easy option) and see if that works, if not disconnect flasher unit and check resistances to bulb earths which also need to be disconnected.
Rich
 diplomacy is a form of art - I was never any good at art
Top
steve f

#9 PostAuthor: steve f » Sat May 26, 2007 8:44 am

Dont listen to all these rubbish posts :lol: just buy a HAYNES manual and read the fault diagnostics page :shock: :shock:
Top
Rich
Hardcore
Hardcore
Posts: 1981
Joined: 4th Mar 2003

#10 PostAuthor: Rich » Sat May 26, 2007 9:14 am

Alternatively replace the flasher unit with a NE555 chip / relay and chuck flasher unit in bin.
Rich
 diplomacy is a form of art - I was never any good at art
Top
User avatar
bunnysZ
Granny Magnet
Posts: 1201
Joined: 7th Mar 2006
Location: herts

#11 PostAuthor: bunnysZ » Sat May 26, 2007 9:26 am

save your money
the advice on here is much better than a haynes manual
but if you do buy a manual a clymer one is better
Top
User avatar
z1bnackerkwacker
100Club
100Club
Posts: 407
Joined: 20th May 2006
Location: Swansea

#12 PostAuthor: z1bnackerkwacker » Sat May 26, 2007 11:45 pm

Agree got a Haynes manual, it's shit, are the Clymers really that much better ?...Will check one out.. :idea:
Top
phil churchett
Hardcore
Hardcore
Posts: 1630
Joined: 28th Mar 2003
Location: Warwickshire

#13 PostAuthor: phil churchett » Sun May 27, 2007 9:02 am

Clymer manuals are good, [much, much better than Haynes].
But if you check out E-bay, genuine ones come up for sale, i sold one on there a while ago, fetched just over ?20, so worth looking/waiting.
Four pipes rule, anything else is second best.
Top
User avatar
z1bnackerkwacker
100Club
100Club
Posts: 407
Joined: 20th May 2006
Location: Swansea

#14 PostAuthor: z1bnackerkwacker » Sun May 27, 2007 2:01 pm

thanx :wink:
Top
User avatar
z1bnackerkwacker
100Club
100Club
Posts: 407
Joined: 20th May 2006
Location: Swansea

#15 PostAuthor: z1bnackerkwacker » Thu May 31, 2007 7:25 pm

phil churchett wrote:Clymer manuals are good, [much, much better than Haynes].
But if you check out E-bay, genuine ones come up for sale, i sold one on there a while ago, fetched just over ?20, so worth looking/waiting.

Just found out they're ?22.99 new.:beer2
http://www.motohaus.com/acatalog/Motoha ... rs_17.html
Top
Post Reply

Return to “Bike Help”

Who is online

Users browsing this forum: No registered users and 72 guests